Biped Arduino Humanoid Robot

I wanted to make a Biped Robot ‘from basics’ instead of a kit, using some sheets of metal that I could saw and bend myself, standard strong servos and an Arduino based development environment.

This is the result so far. It’s a work-in-progress, so I’ll probably make changes to it. The software isn’t done yet, but it can at least crouch and stretch, lift a leg etc.

Here is a video of it’s first steps. It fell forwards after the video was over. Will improve the software and then post it here later.

First steps

The version 1 plans of the robot are as shown on the image.

I basically cut along the solid lines and bend along the stapled lines. In fact I didn’t quite do it as on the plan, but it’s pretty close. There’s a full size pdf available here. The drawing is drawn using CadStd Lite and if you ask you can probably have the original file.
The main components are A and B. The servos are attached in A.

Some comments:

  • Component A could be made a bit narrower (30mm/35mm/30mm instead of 35mm/35mm/35mm), which might help the servos a bit. The servo could be placed along the ‘wall’. Maybe other components could be optimized also.
  • It’s quite tall (about 35 cm or about a foot). That together with no torso, makes it hard to balance. (and no feedback from servos).
  • It requires 12 really strong servos. I’m using Power HD 1501MG, which is said to have torque. The one that struggles the most is the hip that lifts the leg outwards. It might be that the design could be changed to make it easier for that servo.
  • I used a 1mm thick aluminium sheet, but it can probably be done with other materials also, for example steel or plexi glass.
  • I put some bigger feet on it to make it a bit more stable and easy to program, using plexi glass (see the picture).
  • Cut it with a jig or contour saw, drill the holes and bend the pieces along the dotted lines (check YouTube on how to bend sheet metal without special tools). It doesn’t take long to make. Before you drill, use a nail and hammer to make a mark where you want the hole. This makes the placement more accurate and makes it easier to drill.
  • The controller board is a self made AtMega328 board using Arduino as the development environment. It’s using 12 digital outputs to drive the servos. I’m using the servo library that’s part of Arduino. I can share more on the software later, but if you have questions or suggestions, please comment below.
  • I’m using separate batteries for the servos and the electronics to prevent voltage drops caused by the servos to reset the controller. For the servos I’m using a 6V NiMH battery. These servos draw a lot of current, in total somewhere between 5 and 10 A. I wanted to use LiPo batteries, but they’re quite high voltage and will probably damage the servos unless I use a regulator. There are LiPo capable servos, but they’re quite expensive.

If you want to try also, please go ahead using the Attribution + Noncommercial + ShareAlike (by-nc-sa) Creative Common License. Let me know if you have improvements, questions or comments. If you want to make your own biped robot and you find the kits too expensive, this is the way to go. It works, it’s not toooo much work and you learn a lot.
If you’re wondering where the parts go, here’s a picture trying to explain it.

I’ve used a 1mm thick aluminium sheet. It’s probably possible to use both steel and plexiglass instead. Some of the joints would benefit from thicker aluminium or steel.

As the project progresses, I’ll put in some more info here and maybe post a video and some code. If you have comments or questions, please post. I’ve got an antispam on that may make your comment take some time to appear.

Here is a picture of one of the servo mounts in more detail.


67 thoughts on “Biped Arduino Humanoid Robot”

  1. good job guys .. like it …

    i am from india .. i did a similar one for hands.. but long hands.. some how managed to have some torque at 8 volts…

    it would be pleasure to contact you guys to discuss a few things…

    my id is [email protected]….com

  2. For 8 volts, don’t you need special servos? I thought 6 was max for standard cheap ones, though I haven’t tried 8 in fear of burning them.

  3. I don’t think you can do steppers instead of the servos. Stepper motors are typically heavier compared to the weight. The robot would be too heavy.

    About the price. This robot uses 12 metal gear servos, all relatively expensive, so the price is typically relatively high. I would think something like 150-200 USD in total. But you could probably use cheaper servos and also cut out some of the servos, and still be able to walk ok. Hobbyking is a good source for cheap servos.

    It may be that digital servos would be more accurate. My problem with this robot was that without feedback, the battery voltage/charge was not constant, leading to different torque and different behaviour. If I was to do this again, I would add a gyro or accelerometer to compensate, or use feedback on the servos. I’ve been thinking of repeating it with for example the cheap Gyro-board that can be picked out of a 10 USD Wii accessory from That may have prevented it from falling over.

  4. Hi Lars, very cool project using arduino for Humanoid robot, I try your code and compile it code, but coe is error, can you check out your code please?

    the code have comment error like this (stray in program)

    1. 脙漏脗鈥溍偮兟傗好傗好兟ッ偮嵜偮∶兟偮∶偱捗兟偮济偹哘Q1228557129脙炉脗录脗鈥懊兟γ傗懊傗偓脙楼脗鈥∶偮好兟ッ傗澝偮兟ッ偮嵜偮∶兟ッ偮澝傗∶兟っ偮该偮好兟っ偮该傗偓脙搂脗潞脗搂脙楼脗聧脗隆脙娄脗潞脗聬脙炉脗录脗艗脙楼脗鈥γ偮兟γ傗撁偮懊兟γ傗斆偮犆兟っ偮幻偮幻兟っ偮矫傗⒚兟っ偮好偮っ兟γ偹溍傗溍兟偮偮懊兟ッ偮矫傗⒚兟偮济偱捗兟偮得傗灻兟γ傗撁傗劉脙漏脗陆脗聬脙楼脗鈥γ偮兟偮济偱捗兟偱撁偱该兟ッ偮偱久兟偮好偮兟っ偮幻偮矫兟ッ偱犆偱久兟偮惷傗犆兟偮济偱捗兟っ偮好偮γ兟ッ偮徝偮兟γ偱捗傗∶兟ッ偮偱∶兟ッ偮惷偮嵜兟ッ偮傗斆兟ッ偱犆偱久兟偮惷傗犆兟偮济偱捗兟偮偱∶兟っ偮棵偮∶兟γ偮访偹溍兟ッ偮偮澝兟γ傗姑傗γ兟っ偮棵偮澝兟っ偮好偮っ兟γ偹溍傗溍兟偮济偮 脙陇脗戮脗鈥姑兟ッ偮γ傗—脙楼脗聫脗炉脙陇脗禄脗楼脙搂脗禄脗鈩⒚兟っ偮矫偮犆兟γ偮访偹溍兟ッ偮偮澝兟ッ偮好傗斆兟ッ偹喢偮访兟γ偮徝偮惷兟┟偮偹溍兟γ傗毭偮兟偱∶傗灻兟γ偮访偹溍兟ッ偮偮澝兟っ偮棵偮∶兟傗澝偮兟偮偮懊兟ッ偮矫傗⒚兟C傗偓脗鈥 脙陇脗戮脗鈥姑兟ッ偮γ傗—脙陇脗陆脗聽脙娄脗茠脗鲁脙娄脗沤脗楼脙楼脗聫脗鈥斆兟γ偮泵傗∶兟γ偮偮久兟偮济偱捗兟っ偮矫傗犆兟ッ偮徝偹喢兟っ偮该偮嵜兟γ偲捗偮趁兟偮偮┟兟ッ偮偮姑兟γ傗撁偮姑兟偱该偮ッ兟┟偮伱傗溍兟傗∶偮兟ッ偮访偮泵兟偱∶傗灻兟偱撁偱该兟ッ偮偱久兟ッ偮傗溍兟ッ偮惷偮嵜兟C傗偓脗鈥 脙陇鈩⒚偮衡姑兟ッ偮γ傗—脙娄脗鈥毭偮兟γ偲捗偮趁兟偮幻傗劉脙漏脗垄脗鈥犆兟ッ偮偮济兟┟傗偓脗聛脙搂脗陇脗录脙楼脗艩脗啪脙搂脗鈥毭偮姑兟っ偮好傗姑兟γ偲捗傗γ兟偮济偱捗兟っ偮矫傗犆兟γ偹溍偮兟ッ偮徝偹喢兟っ偮该偮嵜兟γ偲捗偮趁兟韭偮┟兟傗∶偮兟ッ偮访偮泵兟偱∶傗灻兟┟偱∶偮惷兟偮偮伱兟γ偱∶偮疵兟┟偱撁偮裁兟偮济偮伱兟偮棵傗劉脙娄脗鈥斆偮睹兟γ傗毭偮兟ッ偮懊偮泵兟┟偱撁傗偓脙篓脗娄脗聛脙楼脗藛脗掳脙娄脗藛脗鈥樏兟っ偮幻偮兟γ偮徝偮惷兟っ偮久傗好兟ッ偱犆偱久兟偮惷傗犆兟偱∶傗灻兟ッ偮嵜偮∶兟偮济偱捗兟γ偹喢傗樏兟っ偮幻偮兟偱∶傗灻兟ッ偮嵜偮∶兟ッ偮徝偮兟っ偮幻偮ッ兟偮偮┟兟γ傗毭偮兟┟偱∶偮徝兟γ傗灻偮徝兟偱∶傗瀉脙篓脗陆脗卢脙楼脗赂脗聬–脙漏脗鈧偮伱兟偮っ偮济兟C傗偓脗鈥毭兟偮幻偯偯兟ッ偮偮⒚兟γ偹喢偮访兟っ偮棵偮澝兟ッ偮傗犆兟っ偮好傗犆兟┟偱∶偮惷兟偮偮伱兟偱∶傗灻兟ッ偮惷偱捗兟γ傗斆偮睹兟っ偮姑偱该兟ッ偱矫偮幻兟┟傗劉脗陇脙陇脗潞脗鈥犆兟ッ偮偮⒚兟γ偹喢偮访兟偱∶傗灻兟ッ偮惷偱矫兟┟偮∶偮久兟っ偮姑傗姑兟ッ偮棵偮兟C傗偓脗鈥毭兟γ偱撁偮兟ッ傗好偮⒚兟┟偹溍偱该兟っ偮幻偮ッ兟偱撁偱该兟ッ偮偱久兟っ偮幻偮C兟ッ偮济傗偓脙楼脗聧脗隆脙拢脗鈧偮怮Q:1228557129脙拢脗鈧傗樏兟ッ偱犆偱久兟偮惷傗犆兟C傗偓脗聛脙楼脗藛脗鈥犆兟ッ偹喢偮兟γ偮徝偮惷兟っ偮久傗7脙楼脗陇脗搂脙漏脗鈥溍偮睹兟偮∶偱捗兟ッ偮嵜偮;脙陇脗赂脗颅脙楼脗鈥好偮矫兟┟傗溍偮睹兟偮∶偱—脙楼脗路脗楼脙楼脗鈥⒚傗犆兟┟傗溍偮睹兟偮∶偱—脙楼脗禄脗潞脙篓脗庐脗戮脙漏脗鈥溍偮睹兟偮∶偱—脙楼脗鈥犆偱撁兟っ偮该偱∶兟┟傗溍偮睹兟偮∶偱—脙陇脗潞脗陇脙漏脗鈧偱∶兟┟傗溍偮睹兟偮∶偱—脙娄脗鈥姑傗好兟ッ傗⒚傗犆兟┟傗溍偮睹兟偮∶偱—脙漏脗鈥毭偮兟γ傗澝偮棵兟┟傗溍偮睹兟偮∶偱抂脙搂脗陆脗鈥樏兟っ偮该偱犆兟┟傗溍偮睹兟偮∶偱捗兟偮济偹喢兟ッ偮徝偮C兟っ偮幻偮っ兟ッ偮嵜偮∶兟偮济偱捗兟傗澝偮得兟ッ偮偮惷兟偮偮伱兟っ偮姑偮γ兟偮济偱扷脙搂脗鈥好偮久兟偮济傗懊兟┟傗⒚偮棵兟γ偱撁偱该兟っ偮久傗好兟ッ偮好傗,脙陇脗驴脗聺脙篓脗炉脗聛脙楼脗鈥γ偮兟γ傗撁偮懊兟ッ偮济傗偓脙娄脗藛脗路,脙陇脗驴脗聺脙篓脗炉脗聛脙楼脗录脗鈧兟γ偹喢偮访兟偮得傗灻兟γ傗撁傗劉脙漏脗陆脗聬脙楼脗鈥γ偮,脙陇脗驴脗聺脙篓脗炉脗聛脙楼脗赂脗娄脙搂脗艙脗鸥脙楼脗庐脗啪脙娄脗艙脗鈥懊兟γ傗⒚偹喢兟ッ偮济傗偓脙娄脗藛脗路脙楼脗沤脗鸥脙陇脗禄脗露,脙娄脗鈥懊偮棵兟γ偱矫偮ッ兟γ偱捗傗∶兟ッ偮偱∶兟ッ偮惷偮嵜兟ッ偮傗斆兟ッ偮济傗偓脙娄脗藛脗路脙娄脗藛脗鈥樏兟っ偮幻偮兟偱∶傗灻兟ッ偮傗斆兟γ傗斆偮兟γ偹溍偮兟偮济偱∶兟偮疵偮兟┟傗∶偮徝兟偮济傗姑兟┟傗偓脗鸥脙楼脗脗脗娄脙炉脗录脗鈥姑兟っ偮棵偮∶兟偮傗懊兟偮济偮伱兟γ偹喢傗樏兟っ偮幻偮兟ッ偮该偱捗兟γ偱撁傗好兟っ偮该偱 脙娄脗艙脗鈥懊兟┟傗⒚偮棵兟γ偱撁偱该兟┟偱撁傗偓脙篓脗娄脗聛脙搂脗拧脗鈥灻兟ッ偮偮⒚兟γ偹喢偮访兟ッ偮幻偮好兟偮傗姑兟┟傗⒚偮棵兟γ偱撁偱该兟ッ偮惷偹喢兟っ偮矫偱撁兟ッ傗γ偮趁兟偮趁偮幻兟偮济偱捗兟ッ偮矫偮济兟γ偮偮っ兟っ偮棵偮∶兟っ偮幻偮幻兟偮济偱捗兟ッ傗γ偮泵兟ッ偮惷偱捗兟偮得偮⒚兟ッ偹喢偮┟兟C傗偓脗鈥毭兟ッ偮γ傗毭兟γ偱撁傗懊兟┟偱撁傗偓脙篓脗娄脗聛脙篓脗炉脗路脙篓脗聛脗鈥澝兟偮趁偮幻兟偮济偮伱兟┟偮澝偱久兟偮偱∶兟ッ傗姑偮棵兟γ傗懊偮懊兟偮济偮 脙楼脗庐脗垄脙娄脗藛脗路脙搂脗拧脗鈥灻兟γ偮幻偮∶兟γ傗灻偮徝兟γ偹溍偮兟γ偹喢傗樏兟っ偮幻偮兟偱∶傗灻兟ッ偮棵偲捗兟γ傗灻偮棵兟γ偮偮⒚兟偮棵偱矫兟ッ傗γ傗懊兟┟偮∶偮久兟ッ傗γ偮兟ッ偮徝偮该兟ッ偮傗斆兟γ傗斆偮兟偮济偱 脙楼脗鈥γ偮兟ッ偮徝偮该兟γ傗懊偮兟偮∶偱捗兟ッ傗好偮矫兟ッ偮偮睹兟┟傗∶傗樏兟偱久偮嵜兟γ傗撁偮姑兟┟傗櫭偹喢兟ッ傗櫭偱捗兟γ傗澝偮棵兟偮傗撁兟偮济偱捗兟ッ偱撁偮兟γ偮趁傗⒚兟ッ偮久傗姑兟C傗偓脗聛脙娄脗鲁脗鈥⒚兟偮傗灻兟偮傗灻兟ッ偮偱∶兟偱∶傗灻兟偱捗偲捗兟ッ傗好偮疵兟ッ傗犆傗γ兟ッ偮济傗偓脙楼脗卤脗鈥⒚兟っ偮该偱∶兟ッ偱犆偮∶兟偮济偱 脙篓脗鈥∶偮兟っ偮该偮幻兟偮幻偮徝兟偮惷偮ッ兟C傗偓脗聛脙篓脗鈥∶偮兟偮疵偱该兟傗好偹喢兟っ偮好偮徝兟C傗偓脗聛脙篓脗鈥∶偮兟γ偹喢傗樏兟偮好偮γ兟γ偮澝偱该兟C傗偓脗聛脙篓脗鈥∶偮兟γ傗姑傗γ兟┟偮C偱矫兟┟傗劉脗漏脙拢脗鈧偮伱兟ッ偹喢傗∶兟ッ偮偱久兟っ偮该偮好兟ッ偮懊偮徝兟っ偮济偮伱兟っ偮该偱∶兟C傗偓脗聛脙楼脗鈥犆偱撁兟γ偮懊傗樏兟C傗偓脗聛脙楼脗鈥犆偱撁兟っ偮该偱∶兟ッ偮徝偱犆兟ッ傗犆偱撁兟γ偮澝傗樏兟偮幻偮徝兟γ偮得偱矫兟偱∶傗灻兟ッ偮徝傗樏兟ッ偮泵傗⒚兟γ偱撁偮嵜兟ッ偱犆偮∶兟C傗偓脗鈥毭兟ッ傗γ偮兟ッ偮徝偮该兟γ傗撁傗∶兟ッ偱捗傗撁兟偮济偱 脙篓脗炉脗拧脙陇脗驴脗隆脙垄脗鈧傗澝兟傗澝偮兟ッ偮棵偲捗兟ッ偮伱偱∶兟っ偮好傗姑兟偮济偱捗兟偮偱∶兟っ偮棵偮∶兟っ偮该偮好兟っ偮好偮 脙篓脗搂脗鈥灻兟偱捗偲捗兟⒚傗偓脗鈥澝兟偮傗灻兟偱捗偲捗兟偮偮∶兟偮惷傗犆兟偮济偱捗兟っ偮久偮澝兟γ偮趁傗⒚兟γ偮裁偮幻兟っ偮济偮 脙漏脗芦脗藴脙娄脗鈥⒚偹喢兟⒚傗偓脗鈥澝兟偱撁偱该兟偮偱∶兟γ偱撁偮嵜兟ッ偱犆偮∶兟偮济偱捗兟┟偮偹溍兟γ傗⒚偹喢兟っ偮久偮棵兟γ偮嵜偮 脙楼脗鈥櫭偱捗兟偮懊偮惷兟⒚傗偓脗鈥澝兟ッ偮惷偱捗兟偹喢偱该兟ッ傗γ偮泵兟γ偮得偱矫兟偮济偱捗兟ッ偹喢傗好兟ッ偮幻偮好兟ッ傗櫭偱捗兟偮懊偮惷兟ッ傗γ偮兟ッ偮徝偮该兟ッ偮徝偮C兟ッ偮徝偮访兟偮济偱 脙陇脗禄脗楼脙楼脗庐脗啪脙楼脗艩脗鈥好兟C傗偓脗聛脙娄脗鈥⒚偹喢兟偱矫傗∶兟偮傗姑兟偮睹偮趁兟っ偮好偱矫兟ッ偮该傗毭兟ッ偱撁偮 脙搂脗鈥澝偮兟γ偱撁偮嵜兟ッ偱犆偮∶兟C傗偓脗聛脙陇脗戮脗驴脙娄脗聧脗路脙娄脗聺脗楼脙篓脗碌脗垄脙楼脗戮脗鈥斆兟ッ偮徝偮C兟偮⒚傗 脙楼脗麓脗鈥∶兟ッ偮懊偱∶兟偮伱偱捗兟っ偮该偱∶兟┟偮伱傗溍兟ッ偮久偮访兟偮济偱捗兟┟偮伱偮得兟ッ偮偹喢兟γ偮趁傗⒚兟ッ偮久傗姑兟γ偮趁傗⒚兟偮傗 脙拢脗鈧傗偓脙娄脗鈧偮ッ兟γ傗毭偮兟γ傗懊傗偓脙娄脗鈧偮ッ兟C傗偓脗聛脙娄脗鈧偮澝兟γ傗毭偮兟γ傗懊傗偓脙娄脗鈧偮澝兟γ偮该偮┟兟┟偮γ偮兟γ偮徝偮惷兟偮っ偮:脙楼脗艙脗篓脙娄脗艙脗卢脙楼脗聧脗隆脙篓脗隆脗艗脙篓脗麓脗颅脙陇脗鹿脗掳脙搂脗拧脗鈥灻兟ッ偮嵜偮∶兟ッ偮徝偮兟傗澝偮兟っ偮好偱矫兟γ傗澝偮睹兟傗斆偮徝兟っ偮矫偮棵兟傗澝偮兟偮济偮

  5. good work but i think, at the robot need ad accellerometer or alse.. and robot need a new perfectioned script for walking .

    1. Yes… this was one of my first projects. There are so many things I would have done differently. Maybe use a gyro/accelerometer etc. Thanks for the feedback anyway.

      1. Sir this is really good project . I want to try like this one .please sir help me with the connection diagram and code please sir

  6. Hello Lars,

    First of all I would like to congratulate you for this amazing project.
    I’m from Brazil, student of Computer engineering, and I’m very interested in your project because I’m developing a conclusion work for my degree about a protesis to inferior members with some colleagues where we’re planning to use arduino as you did.
    I would like to ask you if are you open to discuss some points about your project helping us to solve some issues that we’re having while planning our prototype. We’re “fresh” in these subjects once we just studied the basics in the college.
    your help would be really appreciated, granting you the proper contribution you did in our work.

    Thanks in advance!

    (sorry for my broken English)

    1. Sure, send me questions here or on email (as you have already done). The email alert for my messaging functions aren’t working properly, so safer to reach me on email.

  7. Hey Lars,
    Im an electrical engineering student in my final year, planning to do a humanoid robot as my graduation project, i have looked at this project and it looks great..the design is quiet simple and works fine,it could use some more sensors as you have mentioned.. i was wondering if a torso and an upper body could be developed and attached to this one..what do you think?please let me know if you have any ideas, i would appreciate your help.
    Thanks and best wishes,

    1. I think it would work better with a torso, since this could help balance it. I would consider building some of the parts in plastic to lower the weight.

    1. Good blog! I really love how it is easy on my eyes and the data are well written. I am wondering how I might be notified whenever a new post has been made. I have sueicrsbbd to your RSS which must do the trick! Have a nice day!

  8. you dont happen to know of a similar design for torso,do you? or maybe a link that would help? im actually not familiar with all the mechanical work but trying to learn it… my main idea is the addition of a kinect sensor with an arduino to work as the vision system for the whole robot..but still stuck with the mechanical design!

  9. Hi Lars,

    First, a very nice designed robot. I intend to build a biped robot for my son as a gift. But, as newbie, I don’t have any experience. I would really appreciated if you can share me with your design, specifically, how you mount the servo motors?

    Thank you.

  10. Can I ask for some more detailed information about your bipedal robot? We need to make this for our class and we are hoping you could help us. Your reply is much appreciated. You could contact me through [email protected]. THANK YOU!

    1. Hi. Yes, it’s a bit difficult to see on the picture (you saw the picture with the characters on it, right?). F is on the bottom, glued onto E and D is also on the bottom. Sorry for the late reply. If you haven’t already figured it out or lost interest, I can try to take a better picture. Let me know.

      1. Jo this is so brilliant! I loved it! Although I didn’t know at times whether to laugh or cry as it is so true. I would love to see this published in print – must be somewhere or someone who wo#2&du8l30;.. it so good! Thank you!

    1. A good reason for using a separate controller could also be to have feedback of the servo position. That’d make the controls a lot more accurate (I think).

  11. hi guys
    can any one tell me how does the lower parts fit (D,E and F) a sketch or pictures would be very helpful

    1. The main problem with the servos I use is that there’s no feedback. That makes it very difficult to control, as the servo force reduces when the battery fades. So feedback would improve it tremendously.

    2. wait for it….. in the scene where McG finally removes his pants, Strip can be playing in the bao0Arcund&#823k;..MUSICgL DIRECTION FOR H50, CALL ME!!! (u can all thank me later- I like gift cards)

  12. Hello,
    I read is a AtMega328 board, I use Arduino Mega 2560 R3, their is not errors in code, but doesn’t work in Arduino Mega 2560 R3, somebody knows how to convert AtMega328 to ATmega2560 R3.
    Thanks a lot

    1. The servos are the expensive parts… the aluminium board itself is cheap. Servos would typically be 10-20 USD each for strong enough servos.

  13. do I need to connect the servos in a definite output pin or can we connect it to any output pin.
    And can we connect extra servos then the required number for more power.

    Thanks in advance.

  14. Can you make a humanoid robot with hand legs and height of a human and talking if you can than post it on Google I liked your idea very much its hard for me but I’ll make it its hard because I m of only 12 years where you live

    Purchasing a new or used automobile could be a hard approach should you not know what you are carrying out. By teaching yourself about auto shopping prior to go to the dealership, you can make things easier yourself. The following tips might help your next shopping getaway be pleasant.

    Always deliver a auto mechanic along when shopping for a whole new car. Auto sellers are notorious for marketing lemons and you do not desire to be their next patient. When you can not get yourself a auto technician to consider vehicles together with you, no less than ensure that you have him evaluate your last option before you purchase it.

    Know your limitations. Before starting buying for your forthcoming auto or pickup truck, determine what you can afford to shell out, and follow it. Don’t overlook to incorporate fascination with your calculations. You will probably shell out around 20 % as a down payment as well, so be ready.

    Just before seeing a dealership, know what type of automobile you desire. Study each one of you possibilities just before purchasing so you can decide what works for your budget and loved ones requires. Shop around to discover how much you ought to pay for a prospective car.

    Before you sign any contract spend some time to read every line, like the fine print. If you have nearly anything shown that you just do not recognize, will not indicator till you get an answer that you simply understand. Unsavory salesmen can use a binding agreement to insert numerous costs which were not reviewed.

    If you keep the previous guidance in your mind the next time that you go buying a vehicle, you may be more prone to get a good package. Buying a car lacks to become head ache. Simply use the ideas with this write-up and you will have the car you desire at a very good price.

  16. Hi. I see that you don’t update your site too often. I know that writing articles is boring and time consuming.
    But did you know that there is a tool that allows you to create new articles using
    existing content (from article directories or other blogs from your niche)?
    And it does it very well. The new posts are high quality and pass the copyscape test.
    You should try miftolo’s tools

Leave a Reply to vivek Dave Cancel reply

Your email address will not be published. Required fields are marked *